1 Scope
2 References
3 Definitions
3.1 Terms defined elsewhere
3.2 Terms defined in this Recommendation
4 Abbreviations and acronyms
5 Conventions
6 Optical transport network interface structure
6.1 Basic signal structure
6.2 Information structure for OTN interfaces
7 Multiplexing/mapping principles and bit rates
7.1 Mapping
7.2 Wavelength division multiplex
7.3 Bit rates and capacity
7.4 ODUk time‑division multiplex
8 OTN Interfaces
8.1 Single-OTU (SOTU) interface
8.2 Multi-OTU (MOTU) interface
8.3 Single-OTU with management (SOTUm) interface
8.4 Multi-OTU with management (MOTUm) interface
9 Media Element
10 OCh and OTSiA
10.1 OCh
10.2 Optical tributary signal assembly (OTSiA)
11 Optical transport unit (OTU)
11.1 OTUk frame structure
11.2 Scrambling
11.3 OTUCn frame structure
12 Optical data unit (ODU)
12.1 ODU frame structure
12.2 ODU bit rates and bit-rate tolerances
13 Optical payload unit (OPU)
14 Overhead information carried over the OSC and OCC
15 Overhead description
15.1 Types of overhead
15.2 Trail trace identifier and access point identifier definition
15.3 OTS-O description
15.4 OMS-O description
15.5 OCh-O and OTSiG-O description
15.6 OTU/ODU frame alignment OH description
15.7 OTU OH description
15.8 ODU OH description
15.9 OPU OH description
16 Maintenance signals
16.1 OTS maintenance signals
16.2 OMS maintenance signals
16.3 OCh and OTiSA maintenance signals
16.4 OTU maintenance signals
16.5 ODU maintenance signals
16.6 Client maintenance signal
17 Mapping of client signals
17.1 OPU client signal fail (CSF)
17.2 Mapping of CBR2G5, CBR10G, CBR10G3 and CBR40G signals into OPUk
17.3 Blank clause
17.4 Mapping of GFP frames into OPUk (k=0,1,2,3,4,flex)
17.5 Mapping of test signal into OPU
17.6 Mapping of a non-specific client bit stream into OPUk
17.7 Mapping of other constant bit-rate signals with justification
into OPUk
17.8 Mapping a 1000BASE-X and FC-1200 signal via timing transparent
transcoding into OPUk
17.9 Mapping a supra-2.488 Gbit/s CBR signal into OPUflex using BMP
17.10 Mapping of packet client signals into OPUk
17.11 Mapping of FlexE client signals into OPUflex using IMP
17.12 Mapping of FlexE aware signals into OPUflex
18 Blank clause
19 Mapping ODUj signals into the ODTU signal and the ODTU into the OPUk
tributary slots
19.1 OPUk tributary slot definition
19.2 ODTU definition
19.3 Multiplexing ODTU signals into the OPUk
19.4 OPUk multiplex overhead and ODTU justification overhead
19.5 Mapping ODUj into ODTUjk
19.6 Mapping of ODUj into ODTUk.ts
20 Mapping ODUk signals into the ODTUCn signal and the ODTUCn into the
OPUCn tributary slots
20.1 OPUCn tributary slot definition
Page
20.2 ODTUCn definition
20.3 Multiplexing ODTUCn signals into the OPUCn
20.4 OPUCn multiplex overhead and ODTU justification overhead
20.5 Mapping ODUk into ODTUCn.ts
Annex A – Forward error correction using 16-byte interleaved RS(255,239)
codecs
Annex B – Adapting 64B/66B encoded clients via transcoding into 513B code blocks
B.1 Transmission order
B.2 Client frame recovery
B.3 Transcoding from 66B blocks to 513B blocks
B.4 Link fault signalling
Annex C – Adaptation of OTU3 and OTU4 over multichannel parallel interfaces
Annex D – Generic mapping procedure principles
D.1 Basic principle
D.2 Applying GMP in OTN
D.3 Cm(t) encoding and decoding
D.4 SCnD(t)
encoding and decoding
Annex E – Adaptation of parallel 64B/66B encoded clients
E.1 Introduction
E.2 Clients signal format
E.3 Client frame recovery
E.4 Additions to Annex B transcoding for parallel 64B/66B clients
Annex F – Improved robustness for mapping of 40GBASE-R into OPU3 using 1027B
code blocks
F.1 Introduction
F.2 513B code block framing and flag bit protection
F.3 66B block sequence check
Annex G – Mapping ODU0 into a low latency OTU0 (OTU0LL)
G.1 Introduction
G.2 Optical transport unit 0 low latency (OTU0LL)
Annex H – OTUCn sub rates (OTUCn-M)
H.1 Introduction
H.2 OTUCn-M frame format
Appendix I – Range of stuff ratios for asynchronous mappings of CBR2G5, CBR10G,
and CBR40G clients with ±20 ppm
bit-rate tolerance into OPUk, and for asynchronous multiplexing of ODUj into
ODUk (k > j)
Appendix II – Examples of functionally standardized OTU frame structures
Appendix III – Example of ODUk multiplexing
Appendix IV – Blank appendix
Appendix V – ODUk multiplex structure identifier (MSI) examples
Appendix VI – Parallel logic implementation of the CRC-9, CRC-8, CRC-5
and CRC-6
Appendix VII – OTL4.10 structure
Appendix VIII – CPRI into ODU mapping
Appendix IX – Overview of CBR clients into OPU mapping types
Appendix X – Overview of ODUj into OPUk mapping types
Appendix XI – Derivation of recommended ODUflex(GFP) bit-rates and examples of
ODUflex(GFP) clock generation
XI.1 Introduction
XI.2 Tributary slot sizes
XI.3 Example methods for ODUflex(GFP) clock generation
Appendix XII – Terminology changes between ITU-T G.709 Edition 4 and Edition
5
Appendix XIII – OTUCn sub rates (OTUCn-M) Applications
XIII.1 Introduction
XIII.2 OTUCn-M frame format and rates
XIII.3 OTUCn-M fault condition
Bibliography